KUKKO K-2030-10-S Set of 2 and 3 Arm Pullers with Narrow Jaws

Description

Kukko K-2030-10-S Set of Two- and Three-arm Pullers w/ Narrow Jaws
This Kukko K-2030-10-S puller set is used for removing bearings, gears, discs, etc. for tight or difficult-to-access spaces.
Description:
8 in 1 kit in the tried-and-tested KUKKO-L-Boxx-System.
The set facilitates the assembly of eight different pulling device models through the combination of pulling jaws and extensions.
Flexibility assured thanks to two-arm or three-arm design.
Thin pulling hooks.
Jaw extensions.
Parallel pulling hooks in every position, even with full load.
Pulling hooks with infinitely variable adjustment on the cross-beam.
Optimal adjustment of the spindle to the shaft with 2-sided spindle tip (ball and tip)
Short and long mechanical pressure screws.
Milled thread treated with special coating.
If there is adequate free space around the part to be removed, we recommend using a 3-jaw puller.
Instructions on the cover.
Secure storage in special foam.
Personal KUKKO-Chip-Code
Advantage:
Practical package for universal use.
Can be installed on various pulling hooks and variable reach thanks to jaw extensions.
Turning the pulling hooks enables them to be used both internally and externally.
Suitable for pulling asymmetric workpieces.
2-jaw cross-beam with hexagonal profile for good grip.
Spindle head band prevents the wrench from slipping off.
Almost all components available as replacement parts, time-saving order process thanks to numbering system.
Note: Pressure pads from series 600-17 are a good addition if the shaft is hollow and the spindle cannot be supported.
Stability support from optional series 219 clamp.
Complete easy-to-manage package.
KUKKO-L-Boxx-System compatible with systems by all common manufacturers.
Specifications:
Content:
20-10-SP | Universal 2-jaw puller with narrow jaws, in set
614250 | Mechanical pressure spindle.
30-10-T | Cross-beam
Spare Parts (Sold Separately):
614160 | Mechanical pressure spindle.
614250 | Mechanical pressure spindle.
20-10-SP | Universal 2-jaw puller with narrow jaws, in set
1-91-P | 2 narrow jaws (pair)
1-191-P | 2 narrow jaws (pair)
1-251-P | 2 narrow jaws (pair)
1-91-S | 3 narrow jaws (set)
1-191-S | 3 narrow jaws (set)
1-251-S | 3 narrow jaws (set)
20-10-T | 2-jaw cross bar
30-10-T | Cross-beam
Assembly Set For:
614250 | Mechanical pressure spindle.
20-10-S | Universal 2-jaw puller with narrow jaws
20-10-SP | Universal 2-jaw puller with narrow jaws, in set
30-10-S | Universal 3-jaw puller with narrow jaws
30-10-SP | Universal 3-jaw puller with narrow jaws, in set
20-10-35-S | Universal 2-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
20-10-25-S | Universal 2-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
20-10-2-S | Universal 2-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
30-10-2-S | Universal 3-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
30-10-25-S | Universal 3-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
30-10-35-S | Universal 3-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
How It Works:
The part due to be removed (e.g. a gear, pulley or ball bearing) is gripped from the outside. Tightening of the pressure screw and the resulting pressure removes the part from the shaft.
The puller must be positioned centrally for centre shafts. If the shaft is not sitting centrally, the parts can be removed asymmetrically with pullers with parallel pulling hooks.
Safety Information:
The pulling hooks' sliding parts must always sit stably and fully on the cross-beam.
If several parts have to be removed, always follow a step-by-step process. Do not remove several parts at the same time.
The pulling hooks' support surfaces must always be straight and sit fully beneath the part to be removed.
Do not use any electrical or pneumatic servo screwdrivers or hammer drills.
Protective blanket required.
Protective goggles required.
KUKKO quality standards:
Quality made in Germany.
Strong design, high performance and long service life.
Self-healing corrosion protection KUKKoating for galvanized parts (WITHOUT chrom IV).
Safety label to ensure protection of intellectual property.
A tube of KUKKO special grease included for pressure spindle.
PLEASE NOTE, IMPORTANT INFORMATION:
MADE IN GERMANY
SHIPPING:
FREE SHIPPING!
Please drop us an email for more items not listed in our eBay store.
PAYMENT:
We accept PayPal, Visa/MasterCard, American Express and Discover.
Be sure to add me to your
favorites list
!
Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
Powered by
eBay Turbo Lister
The free listing tool. List your items fast and easy and manage your active items.